Showing results: 1051 - 1065 of 1660 items found.
-
ACMAS Technologies Pvt. Ltd.
Weiber Altitude Test Chamber combine temperature and altitude to test basic components or subassemblies designed for use in a variety of industries. With altitude test chambers, user can control the temperature environment for testing while simulating various altitudes from site level to 10,400 meters (25kPa). Altitude testing may be continued without temperature control up to 600,000 meters (0.1 kPa).High Low Temperature Altitude Test Chamber is used to test temperature and low-pressure altitude conditions simultaneously. Two common applications of High Low Humidity Altitude Test Chamber are testing of avionics or other aerospace equipment to simulate actual conditions, and simulate high-altitude conditions found in mountainous regions or other regions. All models are factory tested, with an ergonomic and maintenance cum user-friendly design. These CE approved test chambers are created with multi-layered insulation with double vapour barrier is of low 'K' factor, high density and of non-hygroscopic in nature. Weiber test chamber are made in accordance with the international standard. Weiber Test Chambers are GMP complaints and are also ISO and NABL certified.
-
PinMap™ -
CAMI Research Inc. (CableEye®)
Check out this fast and super-easy pin-mapping process enabled by our optional CableEye® PinMap™ software. Map as fast as you can move the probe from one pin to the next. Use on your custom connectors, test fixtures, specially-built connector panels, or pigtail adapters to your CableEye tester. This software assigns test point numbers to connector types and applies standard pin designations to the pin numbers. For each custom connector, first choose a connector graphic from our large library to match your connector. Then touch the tester probe to the connector pins one-by-one to automatically detect and assign a test point to each pin. A synthetic voice reads probed pins as you touch them so you don’t need to take your eyes off the connector you’re probing. Finally, enter pin labels of your choice if you wish to override the standard designations.
-
QuickSun® 130E -
Endeas Oy
QuickSun 130E exceeds the ordinary Class A criterions of IEC904-9 ed. 2 with clear margin providing enhanced IV characteristics accuracy. The applicable test methods and procedures are inspected by SGS Fimko Ltd in order to guarantee the compliance and traceability not only with the above standard but also with IEC904-1 ed. 2 which specifies the IV measurement conditions.
-
North Atlantic Industries
The NAI VPX family of power products include a variety of standard features, including continuous Background Built-In-Test (BIT); remote error sensing; and protection against transients, overvoltage, overcurrent, short circuits and over temperature. These intelligent designs also have the flexibility to address special needs. Optional current share is available on main outputs.
-
Multi-Tech Industries, Inc.
Multi-Tech Industries also manufacturers a line of quality instrument-grade electromechanical switches for commercial, industrial, military, institutional and OEM applications. Rotary switches (open frame, enclosed frame), thumbwheel, keyreader and other types are available to be integrated into your process controls or test instrumentation. Standard and custom switch designs can be modified to meet specific customer requirements.
-
DSX -
ARC Technology Solutions
We have developed this technology, not only for our customers, but for our own unique needs in the areas of prototyping and test. We found that many of the standard digital prototyping boards (FPGAs, PLDs, etc…) that are available on the market, did not have the flexibility or the base architecture to provide the prototyping capabilities we need in developing our own solutions.
-
Maintenance Reliability Group, LLC
MRG Labs follows grease sampling and analysis standards outlined in ASTM D7718 and ASTM D7918. Grease analysis is a valuable tool for determining the condition of the lubricant and discovering abnormal conditions in equipment that may otherwise lead to unexpected failures. Our customized grease test slates are designed to identify the specific failure modes that may be damaging the component.
-
19200 -
Chroma ATE Inc.
Support Electrical Safety Test Scanning Support High / Low voltage circuit insulation (Switch module)Support 8 slots for plug-in (removable)Max. 9 slaves for multiple scanners (master/slave interface)Standard RS-232 and USB interface Optional GPIB interface CE Mark19200 can be installed in Chroma Electrical Equipment ATS model 8900
-
rHT SeriesHB SeriesHT Series -
MRC ltd.
Abrasion tester checks the abrasion of solid materials. such as metals, composites, ceramics and more.The test is performed on worn materials such as tires, shoes, belt and more.* Worn out condition* The loss of the weight* The loss of the physical volume* The thickness that been worn out, etc* Use NBS standard gum to ratio the endurance characteristic of abrasion for this material.
-
Tektronix, Inc.
Today's designs are often complex, demanding a variety of stimulus signals during test. With standard waveforms, arbitrary waveform capability and signal impairment options, a Tektronix Function Generator supports a wide range of application needs with one instrument. Best-in-class Function Generator performance from Tektronix AFGs ensures signals are accurately reproduced.
-
6U VME430 6023 -
W-IE-NE-R, Plein & Baus GmbH
The WIENER VME 6023 crate series is the newest generation of 19" integrated packaging system for standard VME/VME64 bus systems with 6Ux160mm cards. Designed primarily for applications in nuclear and high energy physics data acquisition, beam line control and test instrumentation it combines superior mechanical quality with lowest noise power supply technology.
-
Advanced Power Designs, Inc.
Advanced Power Designs manufactures, designs and supports turnkey power supply test systems configured around Chroma ATE Incorporated family of power supply testing components. These systems are PC based systems configured uniquely to meet each customer's requirements using standard Chroma building blocks and other third party instrumentation as needed.
-
Russells Technical Products
Altitude chamber testing is important for manufacturers of products that might be shipped via air. It is especially important for defense and aerospace applications where pressure and vacuum conditions are even more intense. Our altitude test chambers simulate a variety of environmental conditions including temperature, altitude, humidity, and vibration for the rigorous testing standards of combined environment.
-
PTE-FCN -
EUROSMC, S.A.
It is the easiest and most economical way of increasing the relay types that can be tested with the PTE-100-C. The PTE-FCN includes its own LCD display and a BUS-PTE connection, which makes it easier to operate and enables it for use in combination with any other test set in the PTE range. The PTE-FCN is included as standard in models PTE-100-C Pro and PTE-50-CE Pro.
-
IEC60884 Fig20 -
Shenzhen Chuangxin Instruments Co., Ltd.
IEC60884 Fig20 Flexible cord retention force test apparatusMeet the standard: GB2099.1-2008 Article 23.2 and Figure 20, IEC60884 Figure 20, VDE0620 Uses: It is used to check whether the plug wire and the electrical accessory are firmly fixed. Sample range: detachable plug, detachable mobile socket, non-removable plug and non-removable mobile socket
